usb joystick controller board How to Make Your Own Windmill Electric Generator & Solar Panels

by:BLEE     2019-06-30












Use renewable resources such as solar and wind to power your home.Build your own windmill generator and solar panel.Wind turbines are made up of three main parts, rotor, blade and motor, which actually capture wind energy and use wind energy to generate electricity.In turn, this power is connected to the battery pack connected to the inverter, which converts the DC power supply to the AC power supply.Building and wiring solar panels include connecting the solar cells together, then connecting the panels together, to the charging controller of the battery and the inverter, just like a wind generator.Buy motors that produce high voltage at relatively low RPM and high current.To actually generate the rated voltage of the motor, when you use it as a generator, you have to drive it much higher than its RPM rated voltage.Therefore, for your purpose, a motor in good condition with a reasonable rated voltage (Ie., It takes 110 V to power the refrigerator, and the phone charger needs about 6 to 12 volts), the high ratio of voltage to speed is your best choice.Connect the blade to the rotor hub.You can make your own blades using lightweight and cheap PVC tubing and attach them to small length PVC tubing that is used as a rotor hub.If you have never manufactured and assembled blades and rotors before, buy a set of manufactured blades and rotors that, while at a higher price, may produce better results in a shorter period of time.Install the motor on plywood using bolts.At the other end of the plywood, the aluminum tail is attached to keep the generator turned into wind.Install the blade and rotor near the motor and connect the shaft from the rotor to the shaft on the generator.Install the generator--Whether it's on the roof or on the installation Tower.Wire generator to 12-Cable.Connect the black line to the AC motor terminal, connect the white line to the AC motor terminal, connect the green line to the generator installation as a ground.Connect the cable to the blocking diode and then to the charging controller board to route exactly according to the manufacturer's instructions on motor and voltage current.Connect the charging controller board to the dump load to avoid overheating of the battery pack and to the deep cycle battery.Connect the deep cycle battery to the AC inverter.You can use a wind generator to power the appliance.Six single crystal solar cells purchase 36 3 with metal labels on them.The label reduces the amount of welding required to build the panel with the battery.You can also buy larger or smaller batteries.A larger battery generates more current and then more power, but a heavier solar panel.Do not mix larger and smaller cells: larger cells do not reach their full potential.Build a box of plywood (1)e.Plywood 3/8 thick, 3/4 deep) enough to accommodate 36 solar cells.Insert a wooden partition in the shallow box so you actually have two childrenpanels.This will make wiring easier for your solar panels in the future.Cut two thin, rigid, non-Conducting materials (1)e., masonite peg-Board) installed in every half of the plywood box.These are the insulation layers of solar panels.Cut the plexiglass to cover the solar panel and protect it from the weather.Although you can also use the glass, the organic glass is the weather-If hit by rocks, hail, etc., resist and are unlikely to break.Gently drill holes in the center and edge of the plexiglass to facilitate connection to the plywood box.Paint the boards to protect them from the weather and the environment.Paint the peg-Boards on both sides: If you apply only on one side, they curl up due to moisture and damage your solar cells.Arrange the solar cells on the plywood and weld them together in series.In other words, a soldering iron is used to fuse the positive pole of one solar cell with the negative pole of the other.Glue the back of the cell to the plywood by using a drop of silicone caulking agent at the center of each cell.Two sons.Use the panel together 12-Cable.Wire the 12-An ad hoc working group cable measuring the blocking diode.Connect the blocking diode to the charging controller, as described in section 1, to the dump load and depth-Cycle Battery.Wire the deep-Cycle the battery to the AC inverter, which you can use to power the appliance with AC current.Screw the organic glass cover in place.
Custom message
Chat Online 编辑模式下无法使用
Chat Online inputting...