tabletop arcade machine for sale Using a Machine to Mass Produce Wooden Jewelry Boxes

by:BLEE     2019-07-09
tabletop arcade machine for sale Using a Machine to Mass Produce Wooden Jewelry Boxes
This article shows that if your ultimate goal is to produce many of the same, perfect quality products for sale, it is well worth the woodworking machine.As an example, this article discusses a JDSThe router produces a large number of jewelry boxes with matching corners.Some woodworking machines are only used for production work.
This is because it takes a long time to set them up for only one cut.However, if you are going to do the same cut or joint over and over again, the production machine is a way to go.The advantage of positioning production equipment is the accuracy of speed repeatable.
Time is money, quality is everything.
In this article, we will focus on JDS.
The router, an expensive but rather compact fixed woodworking mechanism, has the option of selecting joints including the Mao and Mao, the inclined Mao and Mao, the box joint and the bird tail joint.The Multi-Routers take advantage of routers and various router bits for highly complex cutting on wood.The joint is made of a ball.bearing-Easy to mount to the tip stylus tracking in multiple aluminum templatesRouter.
The workpiece is connected to an aluminum table that can move in and out, left and right, and up and down, controlled by 3 manual levers, one for each shaft.Movement along any axis can be defined with clamping screws and collars included in multiple axesRouter.A particular cut may need to allow the machine to float in both directions without hindrance, while limiting any movement along the remaining Axis.
As an example, how manyThe router works and I will discuss how I can make matching jewelry boxes.The motivation to use the production machine is easy to see: If you can complete accurate and fine work in a very short time, you can produce high outputA lot of high quality goods, so that more sales, therefore more assets.You can also ask for more cash, such as the details of the connecting corner.
Before starting to use my jewelry box, considering that I will find a mechanism to make the same, I have to decide what size is most appropriateInterval tuxedo of the same size.I found that I could do two matching things in the corner of a jewelry box up to 2 1/4.The three Yanwei would ask for an increase in the height of the finished box, which I decided would not be satisfactory.
The next step is stocking.
Completed inventory must have a uniform thickness and width in orderRouter.The final thickness on the side and top of the jewelry box is 3/8 sqm.The base of the jewelry box is plywood 1/8 thick, covered with velvet pads.
The plywood bottom is mounted on a 1/8 saw blade and cut 1/4 above the bottom of the inner wall of the jewelry box.For the sake of economics, I chose to re-measure three thicknesses from each piece of 2 mu (8/4) wood.Before re-scanning, I cut the 2 \ "wood into pieces a little wider than the final size of 2 1/4 (about 2 1/2.
I set the resaw to cut three equal pieces of wood from each piece of raw wood.I then use my SuperMax drum sander to reduce these to 3/8 thick @ 220 thick.These pieces on the table are then torn to the final width (on both sides ).
The final length of 12 Pax (front and back of the jewelry box) and 7 Pax (side), then cut on the mitchsaw using the Forrest ChopMaster blade that left the Mirrorlike cut.On this device, one template is used to cut the tail with a tuxedo knife, and the other is used to cut the pin with a straight spiral cutter.It takes a bit of time to install and waste some wood, so it's better to have some cheap wood of the same size and thickness as the finalwood species.
Table adjustments must be made on the In and Out axis to get the correct cut depth and then lock the position.Detailed manuals and moreRouter, so I don't want to repeat this here.I just want to say that the workpiece is attached to a fixed position on the table, and the left/right and upper/lower axes can float without hindrance when the stylus tracks each template.
Trial and error will give you a perfect fitting in time and you can start producing the final work piece once it is done.If you wish, you can cut the tail at both ends of the jewelry box, both ends of the front and back can cut the pin, and vice versa.Now it goes back to the table and cuts the groove of the plywood floor with a saw.
You must terminate your cut without going through the end of the workpiece.Mark the pencil lines on the saw table and show you where to start and where to end.The idea is to lower the workpiece to a saw blade set to 1/8 above the table.
When the workpiece hits the table, it should be a little earlier than the front stop line.Pull the workpiece back to the parking line before pushing it forward to the rear parking line.For safety reasons, stop the saw before lifting each workpiece from the blade.
Finished, fitted jewelry box piece pushed along with a little Titebond glue while inserting the bottom of the plywood into the 1/8 x94 pre-cut groove.Clip the box Square for 45 minutes.The top of the box can be oversized, polished to 3/8 x94 @ 220 sand and torn to fit the jewelry box.The top can be covered with hinges, or the rear corner can be inserted with brass pins.
Once you have determined the final size of the top, you should be able to install all the boxes safely due to your multiple precisionRouter-made boxes.I like to beat the box and all the corners at the top with a round of 1/8Before polishing.Jewelry boxes and tops should be polished to at least 220 sand by random track Sander and hand before they are completed.
I chose to spray on the gloss (catalytic varnish.You might prefer something else.If you are going to spray, I would like to suggest you make yourself a lazy Susan (hardware part supplied by carpentry ).Take a few pieces of the same size as the bottom of the box 1/8 x94 ply, drill a hole in each corner, and insert the bright flat head box nail into the hole.
The dimensions of the drill should be the same or smaller as the shaft of the nail to prevent the nail from slipping back from the plywood.Place a layer on the Lazy Susan, nail point, and place the box on the top of the nail point.After spraying the box, you can pick it up with plywood and put it aside to dry.
When spraying the top, sharp nail points do not leave visible marks on the finish.The last point is the velvet lining.You need the poster board, 3 m spray-The adhesive on the 1/8 Velcro foam liner and velvet.Velvet can be found in any dry goods store, or other items can be found in craft shops like Ben Franklin or michaels s.
Cut down velvet, extend 1 dash in all directionsSea cutting boardCut out 1x1 square from every corner of velvet (you may have to adjust it to fit the foam liner.) Spray the liner on the poster board.With reference to the poster board, the padding should be cut a bit small.Wrap the velvet on the liner and stick the flaps to the back of the poster board.
The poster board should be pre-Cut into a box that fits perfectly with velvet wrapped on the edge.This may require some experiments, but the final dimension can be repeated over and over again.You can also find velvet, partitioned jewelry box insert tray online.
These are usually only standard sizes, so if you're interested in using them instead of filling the bottom of the simple package described above, you have to design your box around the size of the velvet tray you will be using.Finally, I assume that you can see now that there are a lot of sets in such a production run-Should get up more than work timeEfficiency of repeatable accuracy.On the other hand, I can cut the fit of a box by hand, but they don't look as tight and smooth as they are cut with multiple boxesRouter.
In short, if you want to buy more new or usedRouter, planning to make a lot of jewelry boxes (or something) in each production run ).Woodworking article: Comments on woodworking tools:©Robert M 2010Gillespie , Jr
Custom message
Chat Online 编辑模式下无法使用
Chat Online inputting...